A  B  C  D  E  F  G  H  I  J  K  L  M  N  O  P  Q  R  S  T  U  V  W  X  Y  Z  1  2  3  4  5  *
PROCESS, ENERGY AND GREATER MANUFACTURING products beginning with : P
8201 to 8250 of 22184 results  Page: << Previous 50 Results 160 161 162 163 164 [165] 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 >> Next 50 Results
Plate Edge Bevelling Machines (2 suppliers)
Plate Evaporators (12 suppliers)
Plate evaporators consist of alternating liquid and steam plates, assembled in a manner similar to the plate heat exchangers. The difference between the two systems is that in the plate evaporators, the heating medium is saturated steam, while hot water or hot liquid stream is used for heating in the plate heat exchangers. In addition, plate evaporators are designed to handle evaporating liquid films and vapors produced during evaporation, which are separated in a vapor/liquid separator. Two principal types of plate evaporators are used: rising/falling and falling systems. The plate evaporators use special elastomer gaskets, which can withstand steam temperatures up to 120 degree C, and withstand normal vacuum operation, with boiling temperatures 40-95 degree C.
Plate Fabricating Equipment (1 supplier)
Plate Fasteners (4 suppliers)
Plate Feeders (6 suppliers)
Plate Fin Coils (1 supplier)
Plate Fin Heat Exchangers (35 suppliers)
Plate Fin Heat Exchangers (26 suppliers)
Plate fin heat exchangers consist of a block of alternating layers of corrugated fins. The layers are separated from each other by parting sheets, and sealed along the edges by means of sidebars. In most plate fin-exchangers, the central effective length of the block consists of fining laid parallel to the block axis, to give true counter flow heat exchange among the streams. These direct the flow to gaps in the side bars so as to connect the heat transfer passages with the headers and nozzles, which are welded onto the outside of the block. Large plate fin heat exchangers are made of aluminum and can be up to 1.2m wide, 1.2m deep and 6.2m long. They are most frequently used in low temperature applications, where they give the benefit of a multi-stream capability, ensuring that all the cold streams produced in a process can be used to cool the incoming warm streams.
Plate Fin Heat Exchangers (23 suppliers)
Plate Fin tubular Heat Exchangers (23 suppliers)
Plate Flanges (51 suppliers)
Plate flange is a rib or rim for strength, for guiding, or for attachment to another object. Plate flanges are a widely accepted and cost effective alternative to forged or cast flanges in low-pressure applications. It is generally categorized as blind, slip-on, reducing, threaded, socket weld, angle face and studding outlet. Angle face ring flange is a standard plate flange with a raised face and inside diameter chamfer.
Plate Flash Dryers (2 suppliers)
Plate Flattening (1 supplier)
Plate Formed Anchors (2 suppliers)
Plate Forming (2 suppliers)
Plate Goggles (2 suppliers)
Plate Hardening Furnace Rolls (2 suppliers)
Plate Heat Exchanger Gasket (4 suppliers)
Plate Heat Exchanger Hydraulic Tensioners (3 suppliers)
Plate Heat Exchanger Repair (9 suppliers)
Plate Heat Exchanger Tools (4 suppliers)
Plate Heat Exchangers (84 suppliers)
Plate Heat Exchangers For Pasteurizing (13 suppliers)
Plate Heat Exchangers For Refrigerants (22 suppliers)
Plate Heat Exchangers For Sterilizing (16 suppliers)
Plate Heaters (2 suppliers)
Plate Holders (1 supplier)
Plate Holding System (1 supplier)
Plate Hooks (6 suppliers)
Plate Infeed Systems (1 supplier)
Plate Inspection Systems (3 suppliers)
Plate Joiner Kits (1 supplier)
Plate Joiner Replacement Blades (3 suppliers)
Plate Joiners (2 suppliers)
Plate Lifters (3 suppliers)
Plate Lifting Clamps (7 suppliers)
Plate Liners (2 suppliers)
Plate Lip Buckets (2 suppliers)
Plate Loaders (1 supplier)
Plate Machining (1 supplier)
Plate Magnets (12 suppliers)
Plate magnets are incorporated in chutes and ducts to remove both tramp iron and iron of abrasion. The plate consists of a series of alternating poles, uniform across the chute width and alternating along the chute length. As the material passes over the magnet face, tramp iron is trapped on the magnet face while the remaining non-magnetic material proceeds down the chute. It must be cleaned and inspected daily since they are not effective if the accumulated tramp iron is allowed to remain on the face. The magnetized plates are usually of permanent magnet type, either ferrite or rare earth. The effective depth of the magnetic field can be as high as 200 mm, depending on the type of the magnetic material and on the shape of particles to be removed.
Plate Making Exposure Equipment (1 supplier)
Plate Marking Systems (1 supplier)
Plate Metal Equipments (1 supplier)
Plate Metal Fabrications (52 suppliers)
Plate Mills (6 suppliers)
Plate Mount Mixers (1 supplier)
Plate Mount Open Tanks (2 suppliers)
Plate Mounted Floor Locks (1 supplier)
Plate Mounted Grinding Discs (1 supplier)
8201 to 8250 of 22184 results  Page: << Previous 50 Results 160 161 162 163 164 [165] 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 >> Next 50 Results
Browse Category   |   Alphabetical Products   |   ALL 250,000 Suppliers
HomeBuyAdd FREE ListingAdvertise Industrial CompanyIndustrial Portal