A  B  C  D  E  F  G  H  I  J  K  L  M  N  O  P  Q  R  S  T  U  V  W  X  Y  Z  1  2  3  4  5  *
PROCESS, ENERGY AND GREATER MANUFACTURING products beginning with : C
14801 to 14850 of 25377 results  Page: << Previous 50 Results 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 [297] 298 299 300 >> Next 50 Results
Compression Sensors (6 suppliers)
Compression Services (7 suppliers)
Compression Set Test Fixture (1 supplier)
Compression Skids (1 supplier)
Compression Sleeve Pullers (1 supplier)
Compression Sleeves (6 suppliers)
Compression Software (1 supplier)
Compression Spacers (1 supplier)
Compression Spark Plug Adapters (1 supplier)
Compression Splice Kit (2 suppliers)
Compression Splices (1 supplier)
Compression Sprayers (3 suppliers)
Compression Spring Pull Down Catches (1 supplier)
Compression Springs (293 suppliers)
Compression Springs are open-coil helical springs that offer resistance to a compressive force applied axially. Compression springs are used to resist applied compression forces or to store energy in a push mode. These compression springs are used in automotive, aerospace and consumer applications. Compression springs are a straight cylindrical spring made of round wire. Compression springs are wound or constructed to oppose compression along the axis of wind.
Compression Springs Standard Sizes (1 supplier)
Compression Stacking Connectors (1 supplier)
Compression Stem Adapters (1 supplier)
Compression Stop Sleeves (1 supplier)
Compression Straight Stop Valves (1 supplier)
Compression Strappers (1 supplier)
Compression Swing Check Valve (4 suppliers)
Compression Tanks (3 suppliers)
Compression Tap Holders (1 supplier)
Compression Tee (8 suppliers)
A compression tee is a special fitting. It is designed for tapping into existing metal and PVC pipes. Compression couplings are also used for pipe repairs. A compression fitting works by using a rubber gasket. This gasket is compressed against the existing pipe when you tighten a nut on the end of the fitting. This makes a leak-free seal without the need to thread, glue, or solder the pipe connection. Use metal body compression fittings above ground level, PVC may be used below ground but must be installed below the frost level. Compression fittings may leak if used on heavily corroded, rusty, or pitted pipe. Drip irrigation fittings are also called compression tees.
Compression Terminal Lugs (1 supplier)
Compression Terminals (1 supplier)
Compression Test Adapters (1 supplier)
Compression Tester Kits (2 suppliers)
Compression Testers (28 suppliers)
Compression Testers are of two types, they are tapered rubber-cone type that is inserted into & held against the open sparkplug hole and the screw-in type. Compression testers are threaded into the spark plug openings. Compression testers provide rapid testing & wheel action precise control.
Compression Testing (10 suppliers)
A compression test determines behavior of materials under crushing loads. The specimen is compressed and deformation at various loads is recorded. Compressive stress and strain are calculated and plotted as a stress-strain diagram which is used to determine elastic limit, proportional limit, yield point, yield strength and, for some materials, compressive strength.   It is used to measure the compressibility of a material as well as the recovery of a material that has been compressed to a load and held over a time period.  The maximum stress a material can sustain over a period of time under load (constant or progressive) is determined. This testing is typically used to test plastics, foam, rock, concrete and asphalt. It is rarely used to test metals. It is also used in product testing to evaluate the behavior of finished products. For example, a hypodermic needle may be pushed into a material to see how easily it penetrates and to assess its sharpness.
Compression Testing Machines (27 suppliers)
Compression testing machines are used to determine the compressive strength of concrete cylinders, cubes, and masonry blocks. It is in a high stiffness four-column construction with single acting ram. It features a strain gauge load cell force measuring systems. It is used for measuring load transfer by means of a strain-gauged column.
Compression Tool Kit (2 suppliers)
Compression Tools (2 suppliers)
Compression Track Connectors (2 suppliers)
Compression Tube Adapter Ferrule (1 supplier)
Compression Tube Adapter Nut (1 supplier)
Compression Tube Adapters (2 suppliers)
Compression Tube Connector Ferrule (1 supplier)
Compression Tube Connector Nut (1 supplier)
Compression Tube Fittings (84 suppliers)
Compression Tube Fittings & Connections (1 supplier)
Compression Tube Unions (4 suppliers)
Compression Type Gland Packings (19 suppliers)
Compression Type Springs (5 suppliers)
Compression Unichecks (1 supplier)
Compression Unions (1 supplier)
Compression Valves (4 suppliers)
Compression Vulcanized Moldings (1 supplier)
Compression Wave Transducers (1 supplier)
Compression Weatherstrip (1 supplier)
14801 to 14850 of 25377 results  Page: << Previous 50 Results 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 [297] 298 299 300 >> Next 50 Results
Browse Category   |   Alphabetical Products   |   ALL 250,000 Suppliers
HomeBuyAdd FREE ListingAdvertise Industrial CompanyIndustrial Portal