Condensate pumps are used to collect and transport condensate back into a steam for reheating and reuse, or to remove unwanted condensate from an HVAC or appliance collection pan. There are two basic types of condensate pumps: boiler feed pumps and sump pumps. Typically, condensate pumps and pump components are made of aluminum, brass, bronze, cast iron, plastic, or stainless steel. Important specifications for condensate pumps include power source, maximum discharge flow, maximum discharge pressure, media temperature, tank or reservoir size, and pumps per assembly. Power sources for condensate pumps include AC or DC voltage, hydraulic or pneumatic systems, gasoline or diesel engines, and steam, water, solar power and natural gas. Motor-driven condensate pumps can have a flame-retardant motor and tank cover. They are designed for commercial or industrial use, or suitable for heating, air conditioning, and ventilation (HVAC) applications.

Cone type flanged strainers are available in stainless steel or carbon steel. Cone has raised inner lip design which prevents it from blowing out and down pipeline. All carbon steel cone strainers and orifice plates are identified with blue flange.

Conical spring unbalanced seal is a single-coil conical spring unbalanced seal. These seals are extremely rugged & reliable & therefore used in wide range of sealing applications. Conical spring unbalanced seals have very few parts & hence can be easily assembled or dismantled. The compact design eliminates the requirement of extra radial & axial space for its installation.

Contra Rotating Axial Fans is a modification of the axial-flow fan. It consists of two or more impellers fitted within one casing, which rotate in opposite directions. The arrangement permits the development of high fan pressures of up to 50 mb. These fans are available for auxiliary ventilation in mines.

Controller manifold with quick exhaust valve is used in single controller, multiple well systems to distribute the air signal uniformly to satellite controllers. It is designed for use with all forms of distributed heating systems. It also offers a complete, easily installed energy management system, eliminating the necessity of wiring each thermostat back to the manifold unit.

Conveyor Ball Bearing has in-turned steel with full ball turn, rolled and hardened steel ball rails. They provide side shielding for use in dusty environments. They can be supplied with zinc treatment, zinc-tropicalization, burnishing and phosphate on demand. These idle rolls are used for conveyor plants, fixed or mobile. It has trolley wheels, gravity planes, air chain conveyors and ceramic ovens.

The coolant pump is a centrifugal pump used to circulate the coolant through the coolant passages and into the radiator. The coolant pump is sometimes called the water pump. The pump has a housing with coolant passages. A shaft in the middle of the pump housing is suppoted on a bearing so that it is free to rotate. When the engine is running, a belt or gear drives the shaft. The shaft drives an impeller with curved blades. As the impeller spins, a low pressure is created in the center of the impeller. The low pressure draws in collant. Centrifugal force causes the coolant to be thrown off the tip of the blades under pressure. The pump circulates the coolant through the cooling system. Coolant is pumped from the bottom tank of the radiator. It goes into the engine, the cylinder, and the cylinder head. After circulating around the coolant passages, coolant enters the radiator upper tank.

A cooler is an insulated box, used to keep food or drink cool. Ice cubes are most commonly put in on top of the items, filling in between them. Ice packs are sometimes used, as they either contain the melting water inside, or have a gel sealed inside that also stays cold longer than plain water. Coolers are often taken on picnics, and on vacation or holiday. Where summers are hot, they may also be used just for getting cold groceries home from the store, such as keeping ice cream from melting in a hot car. Even without adding ice, this can be a big help, particularly if having to make another brief stop on the way home.

Cooling Tower Fans remove heat from other materials, usually water. A cooling tower may consist of one cell or many individual cells in a single structure. A single plant may have multiple structures. Cooling tower fans come in two basic types. The first type has the motor mounted to the side of the cell and uses a jackshaft to drive the gearbox in the center. The second type has both the motor and gearbox centrally mounted in the cell. The mechanical components of a cooling tower fan are made up of, motor, jackshaft (optional), gearbox and fan blades. The motor speed for a cooling tower fan is usually 1800 RPM. In cooler climates, the fans can be reversing to prevent freeze during the winter.