Skype
A  B  C  D  E  F  G  H  I  J  K  L  M  N  O  P  Q  R  S  T  U  V  W  X  Y  Z  1  2  3  4  5  *
PROCESS, ENERGY AND GREATER MANUFACTURING products beginning with : G
4751 to 4800 of 6168 results  Page: << Previous 50 Results 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 [96] 97 98 99 100 >> Next 50 Results
Gravity Tracks (4 suppliers)
Gravity Transfers (1 supplier)
Gravity transfers comprise a 4-roller design using 1-3/8 inch diameter rollers with integrated hex shafts. A flexible design which allows for easy removal of the rollers not needed when integrating into a specific application. Available with zinc plated rollers and painted or stainless steel side support braces.
Gravity Tripods (1 supplier)
Gravity Tube Blenders (1 supplier)
Gravity Type Autoclave (2 suppliers)
Gravity Type Conical Feeder (1 supplier)
Gravity Type Magnet Separators (5 suppliers)
Gravity Unit Coolers (4 suppliers)
Gravity V Diverters (2 suppliers)
Gravity Valve (4 suppliers)
A gravity valve is adapted to control the flow of a downhole fluid through the downhole tool. The gravity valve typically includes a plunger and a seat. The plunger embodies a substantially non-spherical end that is adapted to mate with a complementary receiving end on the seat. The increase surface area of contact between the plunger and the seat acts to improve the seal to reduce the stresses thereon, and improve the performance of the gravity valve in general. The components of the gravity valve are constructed of materials, which are selected based on the specific gravity of the materials in comparison with the specific gravity of the downhole fluid for a given application.
Gravity Vented Unit Heaters (3 suppliers)
Gravity Ventilation Systems (3 suppliers)
Gravity Vents (2 suppliers)
Gravity Wagon Augers (1 supplier)
Gravity Wagons (4 suppliers)
Gravity Water Hatch (1 supplier)
Gravity Wheel Conveyors (10 suppliers)
Gravity-Feed Electrical Tape Dispensers (1 supplier)
Gravity-Fit Pendant (1 supplier)
Gravity-Flow Decking (1 supplier)
Gravity-Rise Wheeled Miter Saw Stand (1 supplier)
Gravity/Magnetic Interpretation Software (1 supplier)
Gravure Coaters (2 suppliers)
Gravure Coatings (1 supplier)
Gravure Cylinder Processing Equipment (1 supplier)
Gravure Cylinders (3 suppliers)
Gravure Doctor Blade Systems (3 suppliers)
Gravure Lab Presses (1 supplier)
The gravure lab presses laboratory printing center comprises of separate 12″ wide web gravure and flexographic presses. It access with unwind and power re-wind mounted on a solidly constructed 8 ft. long base.
Gravure Printing Presses (4 suppliers)
Gravure printing presses is an electronic shaft or mechanical shaft drive. It will provide zero-speed butt splice at running speed or flying splice. It has integral or sleeve type printing cylinders and doctor blade with double dual-strike pistons. It has automatic longitudinal and lateral registration control. It will produce accurate pre-registration and rapid correction of registration errors.
Gravure Printing Roll Cleaning Systems (2 suppliers)
Gravure Production Presses (2 suppliers)
The gravure production press model PGP 4530 allows production press with automatic edge guides for stock going into the press and also on rewind. It is mounted on a sturdy base plate. A drying tower over the press can be heated by electrical heaters, steam or piped in hot air.
Gravure Proofing Presses (1 supplier)
Gravure proofing press model SPG-3070 specifically designed to print roll stock or rigid board up to 60 point. It is also specifically designed for hazardous locations.
Gravure Rolls (4 suppliers)
Gravure Systems (3 suppliers)
Gray Bonded Pads (1 supplier)
Gray Bonded Rolls (1 supplier)
Gray Cabinet with Plexiglas Door (1 supplier)
Gray Dusk-To-Dawn Light Control (1 supplier)
Gray Fiberglass Reinforced Plastic Slide Gates (1 supplier)
Gray Finish Spring Loaded Fold-Up Steps (1 supplier)
Gray Food Transfer Hose (1 supplier)
Gray Iron Casting (117 suppliers)
Gray iron casting is used for different types of parts in variety of machines and structures. It is the most versatile of all foundry metals. Its high carbon content is responsible for ease of melting and casting in the foundry and for ease of machining in subsequent manufacturing. The low degree or absence of shrinkage and high fluidity provide maximum freedom of design for the engineer. Their tensile strength can be varied from less than 20,000 psi to over 60,000 psi and hardness from 100 to 300 BHN in the as-cast condition when there is suitable adjustment in composition and selection of casting methods. The hardness can be increased to H Rc 60 by heat treatment.
Gray Iron Castings, Adopter Plates (4 suppliers)
Gray Iron Die Casting (8 suppliers)
Gray Iron Foundries (8 suppliers)
Gray Iron Gravity Casting (4 suppliers)
Gray Iron Investment Casting (2 suppliers)
Gray Iron Sand Casting (11 suppliers)
Gray Light Auto Control (1 supplier)
Gray Mobile Bin Utility Cart (4 suppliers)
4751 to 4800 of 6168 results  Page: << Previous 50 Results 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 [96] 97 98 99 100 >> Next 50 Results
Browse Category   |   Alphabetical Products   |   ALL 250,000 Suppliers
HomeBuyAdd FREE ListingAdvertise Industrial CompanyIndustrial Portal